Our goal is to answer all of your questions, even the ones you haven’t thought of yet! But if we haven’t done that through this page, feel free to reach out! We’re ready to answer even the silliest of questions.
Frequently Asked Questions
Do wells go dry?
Yes, they can go dry. Depending on the aquifer and area you are located.
Does the depth of my well matter?
Well depth varies depending on location. Some locations have a deeper aquifer and others do not.
If I get a price for a new well, what does that include?
We give itemized estimates and can include everything it will take to drill the well and set the pump. It can be difficult to estimate electrical and plumbing to connect the well to the home so we typically do not include that in our estimate for drilling. We do offer electrical and plumbing services to connect the water to your home.
If I drill deeper is the water quality better?
Not necessarily, water quality is dependent on several factors.
How do you determine the best location for a well?
Well locations can vary depending on property size, septic systems, and groundwater districts. We try to work with the property owners if they have a specific location in mind, but sometimes it is out of our control if space is limited.
What distance does my well need to be from my septic system?
In Texas, your well needs to be at least 100 feet from your drainfield and 50 feet from your septic tank. If your well has to be closer due to space restrictions, 100 feet of cement at the top, outside the casing, of the well is required to seal the well, rather than the typical 20 feet.
How long does it take to drill a new well?
The depth of the well and geology at the well site can determine how long it takes to drill. Some wells can be drilled in a day and others can take 3-4 days.
If I am building a new house, when should the well be drilled?
Your well can be drilled at any point during construction. It does not have to be drilled before construction begins, but caution should be taken if there will be heavy equipment (cement trucks, loaders & graders) on site that could run over the well. Keep in mind space restrictions if your lot will be tight once building begins. Most construction sites prefer to have water before the brick laying process begins if there is not an alternative water source.
Why is my water surging?
Water can surge when there is insufficient pressure in your tank. Two components that regulate the pressure are the pressure switch and the bladder in your pressure tank. If these components are not functioning properly, it can cause your water to surge in faucets.
Why do I have good pressure in one part of my house and not the other?
If you notice low pressure in one faucet, but not others in your home, it is most likely not an issue with your well pump. It is typically isolated to that specific faucet and could be debris buildup or a malfunction in the plumbing.
Can you witch for water?
Yes, you can witch for water in areas known to be lacking in water availability. It is not a proven technique to guarantee a water well will produce a sufficient amount for a household. But, it is an option to gather more information on a specific area.
What is the typical lifecycle of a pressure tank?
Most pressure tanks last 7-10 years although some circumstances can cause pressure tanks to fail sooner.
Why do I have little to no pressure?
There are several reasons why you could be experiencing little to no water pressure. It could be an issue with your pump, plumbing, pressure tank, water filter, debris in your lines, or you could have a leak. An evaluation of the system is typically required to determine the cause of low water pressure.
What is the best way to chlorinate my well?
You can purchase chlorine tablets from Currie Drilling Company or we can schedule an appointment to chlorinate. We can also flow and sample your well following chlorinating. The typical sample test for bacteria (E.coli and coliform) and other constituents can be requested or required in some property transactions
Why do I have sand or sediment in my water?
There are a variety of reasons why you have sand/sediment in your water. One could be that your well is overstressed and pumping more water than is available creating sand and silt to be present in your water. This could also be a sign of a pump going out or a hole in your pipe. Sand can also build up in plumbing and fixtures. Currie Drilling can install water filters depending on the type of debris you see in your water. Your well construction or the formation your well is drilled in can allow amounts of sand and silt to be present.
Helpful Links
Texas Department of Licensing and Regulation (TDLR) License Search
Search active TDLR Driller and Pump Installer licenses
Texas Water Development Board (TWDB) Well Search by Map
Use the TWDB Water Data Interactive Groundwater Data Viewer to search for well reports. Click "Groundwater" at the top of the page to view other groundwater data, including plugging reports. Several base maps and layers, along with interactive tools, allow for viewing and downloading Texas groundwater data.
Texas Commission on Environmental Quality (TCEQ) Well Search by Map
Reports that drillers submitted by mail before the inception of the TWDB database are available for access at the TCEQ's website
Panhandle Groundwater Conservation District
The Panhandle Groundwater Conservation District will strive to develop, promote and implement water conservation, augmentation and management strategies to protect water resources for the benefit of the citizens, economy, and environment of the District.
High Plains Underground Water Conservation District No. 1 was created in 1951. As a political subdivision of Texas, HPUWCD is charged with protecting, preserving and conserving aquifers within the District's service area.